Change or rekey · Swansea
Lock Replacement & Upgrade in Swansea
Every morning the front door key needs the same little dance: push in, lift, wiggle, turn. It has been getting worse for a year, and this week it took three tries in the cold before the deadbolt finally gave.
Lock Replacement & Upgrade
In plain words
Sometimes the reason is simply that the hardware looks wrong or has weathered badly. Road salt, freeze-thaw and humid summers are hard on finishes, and a brass handleset can go blotchy while a lacquered knob peels. The locksmith helps you pick a finish that suits the exposure, whether matte black, satin nickel or a PVD brass that resists tarnish, and matches the deadbolt, handleset and interior levers so the entrance reads as one design. Function and grade are chosen alongside looks, so a door refreshed for appearance also comes out better protected.
How the visit goesSomeone tried the back door while you were away. The jamb is splintered around the strike, the bolt is bent, and the knob turns with a grinding feel. Everything held, barely, and you want hardware that would do better next time.
Swansea
How the visit goes
Exposure, weather and finish
The locksmith looks at where the door lives. A side entrance beside a salted driveway, a south-facing front door in full sun and a sheltered porch each treat a finish differently, and the residential hardware label scores finish durability as its own category for exactly this reason. Existing hardware is examined for pitting, peeling and green bloom, which shows how hard the spot is on metal. That guides the choice between a PVD brass, a satin nickel, a powder-coated black or a stainless product, and whether a storm door or a small hood would help. Matching the rest of the entrance comes last, once the finish will survive the location.
Fitting the latch or bolt to the door
Most modern latches and bolts adjust between the two common backsets, so the unit is set to the measured figure and slid into the edge bore. A spring latch goes in with its bevel facing the strike, while a deadbolt is oriented the way its markings or instructions call for, not by that bevel rule. The faceplate should sit flush in its mortise; where the old cut-out differs in shape or size, the mortise is trimmed with a sharp chisel, or a round drive-in collar is used where the door was prepared that way. The bolt is checked to travel freely before anything else goes on, since a bolt that binds in the door will bind under the key too.
Every lock tried the way you will use it
Before the tools go back in the van, each lock is operated from both sides with the door open, then closed, then closed hard against the weatherstrip. The latch should catch on its own when the door swings shut, the deadbolt should throw to its stop with a fingertip on the thumb-turn and no shoulder on the door, and the key should turn without lifting or jiggling. You are invited to try each one yourself and to lock up behind the locksmith. Anything that felt marginal has been adjusted, so the door you close that night behaves the same as the one you tested.
Lock Replacement & Upgrade
In the van
- Key blanks and key cutter
- Adjustable latch or bolt
- Boring jig and hole saws
- 75 millimetre strike and hinge screws
- Cylinders, plug follower and pinning kit
What affects the quote
Same fees day, night or weekend
1Keys cut
Each key is counted, and restricted keys cut against a card are a different item from standard blanks. Say how many people need one and the quote lists them.
2Type of lock
A knob set, a lever, a deadbolt, a full handleset with deadbolt above, a patio door lock and a keypad or smart deadbolt each carry a different hardware cost and take different time to fit.
3Grade of hardware
A light Grade 3 knob set, a residential deadbolt with a strong label rating and a Grade 1 commercial-style deadbolt are different products at different levels, and the quote follows the grade you choose for each door.
Lock Replacement & Upgrade: questions
What does a higher grade of lock actually give me?
Grades follow ANSI/BHMA standards, with Grade 1 the highest and Grade 3 the lightest, and residential hardware carries a separate label that scores security, durability and finish. The grade reports how the lock performed on the standard's own operational, strength and security tests; a higher grade often comes with a longer bolt, a sturdier housing, pins that resist picking and a strike built to anchor into the framing, but those features are worth confirming on the specific model rather than assumed from the grade alone.
Should I rekey my locks or replace them?
Rekey when the hardware is sound and the problem is the key: a lost copy, a move, or too many keys for one house. Replace when the mechanism itself is worn, the housing or bolt is damaged, the grade was never suitable for the entrance, or you want a different function, finish or a keypad. Many visits do both, keeping good locks and rekeying them while replacing the tired ones, all to one key.
My door has glass beside it. Should I fit a deadbolt keyed on both sides?
A keyed interior cylinder means finding a key to get out, which is not what you want on a door people use every day. The steadier answer for a door with glass is a single-cylinder deadbolt with a thumb-turn, combined with a reinforced strike, a longer bolt and a security film or laminated glass in the sidelight.
Change or Rekey Locks
- Deadbolt InstallationThe back door has a deadbolt in name only: a short bolt, a thin brass strike held by two little…
- Vintage Mortise Lock ServiceSomeone painted the door years ago without removing the hardware.
- Smart Lock InstallationHalf the evenings someone asks whether the back door got locked, and nobody is sure.
Lock Replacement & Upgrade near you
Doors in Swansea are opened, rekeyed, repaired, reinforced and replaced by the same small team, so you can pick one service today and add another later without explaining the house all over again. Start with the page that matches your door; the rest of the list will still be here.